VW Vortex - Volkswagen Forum banner

New Product Development 2.5L L/W Single Mass Flywheel and Clutch kits , Shipped Ground Lower 48

191K views 145 replies 49 participants last post by  FourSeasonTuning.com 
#1 · (Edited)
Flywheel and Kits Below




FST 228MM L/W Single Mass Steel Billet Flywheel Includes Ring Gear $324.95 Shipped Ground ,

FST 228MM L/W Single Mass Steel Billet Flywheel Without Ring Gear $309.95 Shipped Ground ,

FST 228MM L/W Single Mass Alloy Flywheel Includes Ring Gear $389.95 Shipped Ground ,

FST 228MM L/W Single Mass Alloy Flywheel Without Ring Gear $369.95 Shipped Ground ,




FST 228MM L/W Single Mass Alloy Flywheel W/ Sachs VR6 Clutch Kit $559.95 Shipped Ground ,

FST 228MM L/W Single Mass Steel Billet Flywheel W/ Sachs VR6 Clutch Kit $499.95 Shipped Ground ,



FST 228MM L/W Single Mass Alloy Flywheel W/ Clutchnet Stage 2 VR6 Clutch Kit $749.95 Shipped Ground ,
FST 228MM L/W Single Mass Steel Billet Flywheel W/ Clutchnet Stage 2 VR6 Clutch Kit $679.95 Shipped Ground ,



FST 228MM L/W Single Mass Alloy Flywheel W/ Clutchnet Stage 3 VR6 Clutch Kit $759.95 Shipped Ground ,
FST 228MM L/W Single Mass Steel Billet Flywheel W/ Clutchnet Stage 3 VR6 Clutch Kit $694.95 Shipped Ground

OEM 2.5 Dual Mass Flywheel W/ Ring Gear 22.7 LBS
OEM Clutch Disc & Pressure Plate 10.1 LBS
Total Weight 32.8 LBS

FST Alloy Single Mass Flywheel/ Ring Gear 10.0 LBS
Sachs VR6 Clutch Disc & Pressure Plate 13.1 LBS
Total Weight 23.1 LBS
Total Overall Weight Reduction 9.7 LBS W/ Alloy FW

FST Steel Billet Single Mass Flywheel/ Ring Gear 14.0 LBS
Sachs VR6 Clutch Disc & Pressure Plate 13.1 LBS
Total Weight 23.1 LBS
Total Overall Weight Reduction 5.7 LBS W/ Steel

By using a heavier Clutch Disc & Pressure Plate this will add 3 more
pounds to the Alloy flywheel (as compared to the OEM 2.5 Clutch Disc &
Pressure Plate ) making it feel like a 13 pound flywheel. This overall
weight reduction is 9.7 pounds. A steel version could be made if the
alloy one ends up being too light and or a heavier version is wanted.

Here are some examples of other weights of OEM Flywheels (Engines of
similar power)
All OEM Single Mass Cast VR6 12V flywheels are 17.75 pounds w/ ring gear.
Many users have switched to a L/W Steel Billet Flywheel that weighs in at 11.75 w/ ring gear fitted.
Also available are slightly heavier Cast steel Single Mass w/ ring gear at 13.80 pounds ( still lighter than stock).

MK4 1.8T W/ 5 speed users are changing the OEM DM 22 pound flywheel
and converting to A Single Mass as well.
Again using the same weight as a 12V VR6 single mass steel billet
flywheel that weighs in at 11.75 w/ ring gear fitted.Also available
are slightly heavier Cast steel Single Mass w/ ring gear at 14
pounds.Both of the these flywheels were created in the aftermarket as a
performance part designed for the Corrado G60 and are using the very
proven Sachs VR6 clutch kit ( this Sachs kit is rated to 250-275
Torque and takes more)

1.8T & 2.8 24V VR6 W/ 6 speed 02M 6 speed users are changing the OEM DM
26.5 pound flywheel to A Single Mass type as well. 16.5 single mass
steel billet w/ ring gear this takes 10 pounds off and does not chatter.

Clutch Kits without Flywheel

2.5L Stage 1 Clutch Kit $215.00 Shipped Ground ( Includes 228MM Sachs Pressure Plate, Sachs Sprung Hub Disc,Sachs T/O bearing. Rated at 275 TQ at flywheel.Must be used with FST228-2.5AFW.

2.5L Stage 1 Clutch Kit


2.5L Stage 2 Clutch Kit $375.99 Shipped Ground ( Includes 228MM Clutchnet Yellow Pressure Plate, Clutchnet Disc w/ Steel covered 6 spring Hub,Sachs T/O bearing and alignment tool. Rated at 375 TQ at flywheel.Must be used with FST228-2.5AFW.

2.5L Stage 2 Clutch Kit

2.5L Stage 3 Clutch Kit $554.95 Shipped Ground ( Includes 228MM Clutchnet Red Pressure Plate, Clutchnet Disc w/ Steel covered 6 spring Hub, Sachs T/O bearing and alignment tool. Rated at 445 TQ at flywheel. Must be used with FST228-2.5AFW.

2.5LStage 3 Clutch Kit

2.5L Stage 2X Kevlar Clutch Kit $445.00 Shipped Ground ( Includes 228MM Clutchnet Red Pressure Plate,Kevlar Clutchnet Disc w/ Steel covered 6 spring Hub, Sachs T/O bearing and alignment tool. Rated at 400 TQ at flywheel. Must be used with FST228-2.5AFW.

2.5L Stage 2X Clutch Kit

2.5L Stage 2X Fiber Carbon Clutch Kit $445.00 Shipped Ground ( Includes 228MM Clutchnet Red Pressure Plate,Fiber Carbon Clutchnet Disc w/ Steel covered 6 spring Hub, Sachs T/O bearing and alignment tool. Rated at 400 TQ at flywheel. Must be used with FST228-2.5AFW.

2.5L Stage 2X Clutch Kit




California residents will be charged 7.75 % sales tax.

The current site only has a fraction of the parts listed that we carry.Please contact us if the items you seek are not on the site. Competitive pricing, Fast shipping, If you see a lower price let us know, chances are we can work with you.

Questions at 714-997-5842 M-F 10-6 PST

Email is better than IM
sales(AT)fourseasontuning.com*

Thanks for looking.
James

AKA wld101turkey
 
See less See more
9
#5 ·
Re: FV-QR (Lloyd Plumtree)

Thanks for the bump.
Can count the ring gear teeth on Monday. As far as an 02A/02J swap, The height of the ring gear and the overall stack height on the 2.5L is much different than the 12V VR6 / G60 flywheel and clutch setups. I would try the the single mass set up like this
http://www.fourseasontuning.com/?product=101 as it works with the 02A/02J for sure.

The general rule of thumb has been use the flywheel/clutch kit/ starter that was designed to work with the transmission code regardless of the engine. Most VAG flywheel's have been 6, 8 and 10 hole at the Crank flange. For example the step and stack height are the same on the 02A /02J. The 6 hole flange is used on the 4 cyl and the 10 hole on the VR6. Same goes for the 02M six speed stuff the 1.8T and 2.8 24V VR6 are the same setups except for the amount of holes in crank.
The 2.5 5 speed is very similar to the 02J.
 
#9 ·
Re: (daemontrym)



The dual-mass flywheels absorb engine vibrations before they are transmitted to the driveline where they can create gear rattle. The unit is split into two sections: a primary section that bolts to the crankshaft, and a secondary section, onto which the clutch is bolted. The primary section dampens, isolates engine vibrations.
VW has be building internally balanced engines. High CI V8 are often externally balanced engines.
If you're rebuilding an engine that is internally balanced, the flywheel and damper have no effect on engine balance and can be balanced separately. But with externally balanced engines, the flywheel and damper must be mounted on the crank prior to balancing.
 
#10 ·
Re: FV-QR (FourSeasonTuning.com)

Quote, originally posted by FourSeasonTuning.com »
Thanks for the bump.
Can count the ring gear teeth on Monday. As far as an 02A/02J swap, The height of the ring gear and the overall stack height on the 2.5L is much different than the 12V VR6 / G60 flywheel and clutch setups. I would try the the single mass set up like this
http://www.fourseasontuning.com/?product=101 as it works with the 02A/02J for sure....
The general rule of thumb has been use the flywheel/clutch kit/ starter that was designed to work with the transmission code regardless of the engine. Most VAG flywheel's have been 6, 8 and 10 hole at the Crank flange. For example the step and stack height are the same on the 02A /02J. The 6 hole flange is used on the 4 cyl and the 10 hole on the VR6. Same goes for the 02M six speed stuff the 1.8T and 2.8 24V VR6 are the same setups except for the amount of holes in crank.
The 2.5 5 speed is very similar to the 02J.


Guess I should have stated some more info. I`m planning to mate a 02A trans to my 2.5L motor (which is going into a MK3) I`m aware of the flywheel/crank bolt patterns. Just wondering if a 2.5L clutch kit will be needed to complete this conversion. Guess I`ll just bolt it up and see what I come up with.
 
#20 ·
Re: (R-a-p-e stove)

From this I gather that the vR6 clutch will work with the OEM tranny in a 2.5L MKV...if that's correct....do you have torque ratings from Sachs for the Vr6 clutch vs the OEM MKV 2.5 clutch?...Thanks! http://****************.com/smile/emthup.gif
 
#22 ·
Re: (FourSeasonTuning.com)

Changing from a DMF to a solid damper would effect the torsional vibration levels of the crankshaft resulting in different crankshaft stresses. It would be interesting to see what impact, if any, the change to rotational inertial and damping rate on the drive end of crankshaft has on overall crankshaft stresses. I imagine there is healthy fatigue margin in automotive crankshafts since crank failures are extremely rare in automotive applications running at rated powers. Being involved in large Diesel engine development and worked on crankshaft torsional testing this is not something I imagine aftermarket suppliers have the resources or testing equipement to measure but in the off chance this was done would be interesting to see the plots
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top