VW Vortex - Volkswagen Forum banner

VR6 DYNO N/A

138K views 69 replies 51 participants last post by  PowerDubs 
#1 ·
VR6 Dyno's N/A

pls post pick of dyno graph and setup
Engine:
 
#51 ·
My VR6 N/A Dyno grafic

I hope all enjoy the info of my Time Trial VR6 GTI

Anyone can see that the car was doing more WHP at the end of the grafic but that's the point that i can't tune because is the factory rev limiter.
The car just has custom intake & exaust/cams with Hardcore/212 Tuning from Puerto Rico
Pics of the car
 
#54 ·
Re: (root beer)

I just dyno'd my cabrio vr6 today. I did 171whp and 157wtq.
Mods are:
Autotech chip
P&P big valve head
stock cams
155k miles on stock bottom end with mk3 headgasket
2.9 clone intake manifold
stock exhaust manifolds
modified airbox with k&n
I thought the numbers were decent till i came back looking in here. Oh well. I ditched the TT 268 cams and obx header I was running in favor for stage 2 VF. Cant wait to put that on, will be running 36lb injectors, 4" maf housing and c2 software with the 8psi pulley.




Modified by baupfhor at 2:37 PM 4-12-2008
 
#56 ·
Re: (1_slow_mk3)

Here is mine, not so proud but this is what i got.....

 
#57 ·
Re: (Mr_Long)

no graph but dynoed at aptunings dynojet and got 164 hp and 157 tq with neuspeed intake w/heatshield,abd big bore,2.5 custom exhaust w/borla,testpipe,eip stg. 2 chip,2.9 manifold,262 cams,hd valve springs,mk4 headgasket and i think thats all pulls where in 3rd gear and the bottom end had 240k and the head has about 5k on the rebuild
 
#58 ·
Re: (steve-o 16v GLI)

just ran it saturday. 3rd gear
mk2 jetta
2.8 12v vr
190k on block( stock)
no head work other than
tt 288's with light weight lifters, hd vavle springs, stock head gasket
tt chip
7lb flywheel
bfi mounts
cai
autotech cat back, test pipe
all stock manifolds, and down pipe
a/c delete

also 2 other 12v's with diferent cam's ran that day as well,one ran 156, the other was 164


Modified by Jr Smith at 4:29 PM 10-27-2008
 
#60 ·
Megasquirt NA VR6

Ported and Polished Big Valve Head (built by me)
41mm Intake, 36mm Exhaust, Light wieght mk 4 INA lifters, Schrick Valve Springs, DRC 268's
10 lbs flywheel
SAI deleted
EGR deleted
no power steering
no A/C
Ported Intake Manifolds, Polished Exhaust Manifolds
2.5" cat back custom exhaust with flowmaster muff
Dyno Tuned MS1_Extra using EDIS Code 29V - did the tuning during a dyno day and was limited to 6300 rpm...think there would be a little more up top
according to the graph
201.6 whp 185.4 ft lbs
 
#61 · (Edited)
12v corrado OBD1 Dizzy



Piper 270 cams
1.8T IAT
Powergasket
MBS 3" Full Exhaust no cat
MK4 HG
2.9 Clone intake
2.9 TB
CAI
Autotech Qchip
Autotech LFW

Was dyno'd on a mustang dyno (heartbreaker)

179 wHp
179 Tq
Leaking valve seals :(

gonna have the head redone and Port the stock Exhaust Manifold/dp along with a GIAC chip
 
#65 ·
have a picture but cant load it ... sucks

not much but its what i got

HP: 186.6
TRQ: 173.8

163k on the bottom end , about 5k on the top end
MODS :
HEAD:
2.9 clone intake k&n filter (p&p)
stock valves
head ported and polished (gasket matched)
262 auto tech cams
mk4 lifters
mk4 head gasket
stock injectors

GIAC chip ( non cam profile)
no a/c
2.5inch exhaust cat back w/ cut out
(need to port out the exhaust manifolds)
or run hood exit exhaust


11.7 afr*
 
#66 ·
Stock 12v VR6 with cams, and bolt ons. Center feed short runner intake manifold, raceland header, MS3 Pro Ultimate supplied and tuned by Paul Kiernan from kptuned.com

200 hp, 175 tq.

Am going to the dyno Wednesday with the new setup and M5. Ill update after then. Video is from last season.


https://www.youtube.com/watch?v=-HITXRTGH4I
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top