Search Results - VWVortex
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    Fourtitude.com


    Search:

    Type: Posts; User: need_a_VR6

    Page 1 of 150 1 2 3 4

    Search: Search took 0.40 seconds.

    1. Replies
      2
      Views
      209

      Likely problems with vvt with that much removed....

      Likely problems with vvt with that much removed. Done .030Ē on a 12v but only skim the 24v as little as needed.

      My advice buy pistons w the right compression height.
    2. Replies
      2
      Views
      94

      Good mounts and bushings go a long way. As you...

      Good mounts and bushings go a long way. As you said the last piece is tires. Slicks wonít hop.
    3. Replies
      57
      Views
      17,647

      That makes sense if measuring the ms side. 12v...

      That makes sense if measuring the ms side. 12v would mean the output is off, ground would be on.
    4. Replies
      57
      Views
      17,647

      Wire colors are right make sure you are checking...

      Wire colors are right make sure you are checking the right pins. Most diagrams are shown looking at the connector back toward ecu, so if you are looking at the harness connector unplugged it would be...
    5. Replies
      247
      Views
      53,084

      Just got a kit for the pins if it happens again

      Just got a kit for the pins if it happens again
    6. Replies
      247
      Views
      53,084

      Crank pulley came off again on a test hit on Sat....

      Crank pulley came off again on a test hit on Sat. Key is gone and crank is .035Ē under where it should be. Luckily its less than .001Ē out of round. Fix for now is a shim in the pulley to take up the...
    7. Replies
      57
      Views
      17,647

      Those pin # sound odd as 1-2 and 7-19 are all...

      Those pin # sound odd as 1-2 and 7-19 are all grounds in a normal ms harness.
    8. Replies
      174
      Views
      12,885

      Donít do #1. I know fourthchirpin found something...

      Donít do #1. I know fourthchirpin found something to work. Will alert him to your q.
    9. Timing if anything looks aggressive. You can...

      Timing if anything looks aggressive. You can loose power from too much even without knock.

      Also verify WITH A TIMING LIGHT that when timing is set to 0deg fixed that you see the tdc mark on the...
    10. The stock fuel system on a cis car will outflow a...

      The stock fuel system on a cis car will outflow a walbro 255 readily and out do the aem at higher pressures.
    11. Replies
      42
      Views
      1,040

      I learned that after a point obd1 will fight you...

      I learned that after a point obd1 will fight you and it will win. Then you end up on standalone.
    12. Replies
      174
      Views
      12,885

      The ecu uses timing as part of the idle...

      The ecu uses timing as part of the idle stabilization strategy. I would be more worried if it didnít jump around.
    13. Replies
      42
      Views
      1,040

      Yeah I know how that one ends up. Just get...

      Yeah I know how that one ends up. Just get standalone now before you lose your hair like I did.
    14. Replies
      42
      Views
      1,040

      If standalone is an option you can easily run the...

      If standalone is an option you can easily run the 60-2 with a waste spark coil and no distributor at all.
    15. Replies
      12
      Views
      598

      Not sure about the mil code but I think you cant...

      Not sure about the mil code but I think you cant have any sai codes to enable fuel trim. Plug the relay back in and see.
    16. Replies
      42
      Views
      1,040

      See above, no one does it because anyone that has...

      See above, no one does it because anyone that has done it is now too old to remember.

      I remember the 20v cam gear but thats about it and I did it at least twice.
    17. Power seems a little low for e85, we get that...

      Power seems a little low for e85, we get that much on pump gas without issues. Likely needs timing adjusted, but will be low 30s psi for 550whp.
    18. Replies
      247
      Views
      53,084

      New crank ...

      New crank

      https://uploads.tapatalk-cdn.com/20190408/7e9a676eca4de85e2ae1d2819a3f984b.jpg

      New front main

      https://uploads.tapatalk-cdn.com/20190408/94ba7614d40a69aaf300b59d8d0bdb05.jpg

      New...
    19. Replies
      12
      Views
      598

      I know the power wire is blk/yel but not sure on...

      I know the power wire is blk/yel but not sure on the signal.
    20. Replies
      12
      Views
      598

      Good question I dont have a solenoid to measure...

      Good question I dont have a solenoid to measure but would be the same as the 1.8t guys use.
    Results 1 to 20 of 3000
    Page 1 of 150 1 2 3 4