Search Results - VWVortex
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    Fourtitude.com


    Search:

    Type: Posts; User: DbilasTDI

    Page 1 of 21 1 2 3 4

    Search: Search took 0.06 seconds.

    1. Replies
      5
      Views
      353

      https://www.supersprint.com/ww-de/sportauspuff-anl...

      https://www.supersprint.com/ww-de/sportauspuff-anlage-supersprint-vw-passat-3c-r36-4-motion.aspx
    2. Replies
      5
      Views
      350

      do you have fresh premium gas?

      do you have fresh premium gas?
    3. You have a misbehaving 19 year old VW automatic...

      You have a misbehaving 19 year old VW automatic trans and you use the words "mechanic sabotage?" I would guess auto trans failure a top reason those gen cars end up in a junkyard with no obvious...
    4. Replies
      25
      Views
      1,254

      You would need to balance everything statically:...

      You would need to balance everything statically: rods pistons rings pins
      Then have it dynamically balanced (spinning) crank, front pulley, lightened flywheel, clutch, all assembled

      This is a bit...
    5. It has never been a lot of oil in the puke tank,...

      It has never been a lot of oil in the puke tank, especially with the vaccum pulling now. I empty it less than once/year. I probably drive 1500-2000 miles a year. I dont have numbers but at steady...
    6. Replies
      1
      Views
      397

      I dont think they are going to work for you. The...

      I dont think they are going to work for you. The newer VW heated seats us a PCM control signal - a square wave of varying duty cycle depending on the setting of the control. I just tore down a 2014...
    7. Replies
      10
      Views
      1,123

      I use a dipstick from an old 1.6. Only comes up...

      I use a dipstick from an old 1.6.
      Only comes up 2-3 inches above the dipstick tube.
      I use a coat hanger "fish hook" to assist because the dipstick handle is right next to the front carb.
      I also...
    8. I bought a Cheena puke tank off ebay - mounted to...

      I bought a Cheena puke tank off ebay - mounted to right fender in front of EDIS coils

      It "helped" but was only venting to atmos

      Enter the DBilas carb plenum with internal filter

      In the top...
    9. Replies
      19
      Views
      11,564

      Use an old radiator hose with a bend near the...

      Use an old radiator hose with a bend near the end. poke a hole for the blaster tube in the outside of the bend. The hose will seal up the port. Other end of hose to shop vac
    10. Replies
      4
      Views
      615

      send your pump to Canada for a Giles build. This...

      send your pump to Canada for a Giles build. This guy is THE wiz.

      http://performancediesel.ca/performance.htm
    11. 3.6 swap into MK2 downpipe O2 sensors and the lot

      So I have a 2014 CC 3.6 going into a MK2 GTI.
      Going to utilize Malone for the software
      What about the 4 kats and 4 O2 sensors?
      I can have a straight downpipe with one sensor or 2
      I can do 2 cats...
    12. Replies
      1
      Views
      542

      dont do it. Those fans only exist because a...

      dont do it. Those fans only exist because a scirocco radiator became a standard for drag racers. The fans will not last long. If you need more cooling the S&P radiator is great and has a good fan...
    13. Replies
      11
      Views
      1,487

      I have changed several times so this was kinda a...

      I have changed several times so this was kinda a wire as you go project. I used a S&P Radiator, stock temp switch and a relay for the fan
      https://i.imgur.com/JGQhBCZ.jpg
      1 relay feeds the Ford...
    14. 2014 CC AWD 2 factory rims 1 new with brand new rubber

      Car had 55K on it that fateful day. Spare rim and tire unsed minty fresh from the trunk. OEM Contineltal Rubber. One used rim unmarred. $400 Nashville TN...
    15. Replies
      23
      Views
      1,229

      84mm no problem ABT did 84 in 1.8 16V Bertil...

      84mm no problem
      ABT did 84 in 1.8 16V
      Bertil did 85 in high$ racing engines

      specify a chamfer on top edge of piston and you can use stock gasket

      I built a 84 x 94.5 into a 1.8 16V and 84 x...
    16. Replies
      12
      Views
      1,116

      Veicomer appears to be selling dimpled heads all...

      Veicomer appears to be selling dimpled heads all the time. They certainly do it to all kinds of heads, even 3.6

      After looking at the size of these ports and how nice the finish is and not...
    17. Replies
      9
      Views
      788

      These engines are designed to not need a drop. ...

      These engines are designed to not need a drop.

      I do like to glue the gasket to the pan with a few bolts to hold in alignment. This is just for ease of installation and typically it will last...
    18. Replies
      10
      Views
      937

      Get the Mitsubishi bolt from ARP - it may be a...

      Get the Mitsubishi bolt from ARP - it may be a smidge too long but it is a bitchin bolt so shorten if you need to. Follow the ARP directions

      I think that bolt is 195 ft lbs best to have car on...
    19. Replies
      23
      Views
      1,229

      You gotta buy pistons and the size does not...

      You gotta buy pistons and the size does not affect the price. 84mm 11:1
    20. Replies
      11
      Views
      1,487

      I used their 12 circuit setup on my Rabbit truck....

      I used their 12 circuit setup on my Rabbit truck. Nice stuff and reasonable.Get an assortment of weatherpack connectors to use anywhere you may need to disconnect sonething for servicing, perhaps...
    Results 1 to 20 of 419
    Page 1 of 21 1 2 3 4