Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    Fourtitude.com


    Search:

    Type: Posts; User: HGB

    Page 1 of 13 1 2 3 4

    Search: Search took 0.71 seconds.

    1. center cap

      That I know as thats the way they came on the older trans, just did it for the hell of it and to keep the flanges out on the clip. In theory it would rub while turning, but after 8 years, its has no...
    2. center caps

      Hey. Well there is an older style center cap, metal and hole in the middle that is covered in rubber, it is thicker and would solve the issue. I just to a trans apart and tossed these away so I am...
    3. Replies
      4
      Views
      499

      trans

      Check the shifter cable, fluid level first. Is this all the gear including reverse?
      Any noise like a whine when shifted into gear?
    4. Replies
      2
      Views
      378

      trans

      It would sound like a worn or cracked synchro. Flushing wont work, it has to be removed opened up and verified.
    5. Replies
      1
      Views
      303

      trans

      More than likely the over center spring inside the trans broke. If it breaks then reverse gear and 1st gear tries to rub each other which give you the noise. Got to open it up to repair the issue.
    6. Thread: Vr6 tranny help

      by HGB
      Replies
      2
      Views
      352

      trans

      More than likely the input shaft bearings are worn. Or and bearing under and of the driven gears
    7. Replies
      4
      Views
      481

      trans

      Try bleeding bleeding the master cylinder first, cap it off, then fill the slave cylinder slowly...slowly so the fluid can go in and the air come out. Now connect the line and finish bleeding it...
    8. Replies
      2
      Views
      406

      trans

      More than likely when you dropped in the pothole and out of it, the wheel was air born for a split second and when the wheel touch the road again it slowed down the trans immediately which then takes...
    9. Replies
      3
      Views
      627

      noise

      Need more info.
      That noise almost sound like the exhaust manifold heat shields or a loose converter.
      Did you try to isolate the noise to the trans?
    10. Replies
      1
      Views
      568

      trans

      Is this noise a constant click/tap while in that particular gear?
      Or is it a click as you shift into a gear?
      It sounds like a bearing issue or possibly a broken / tooth on the ring or pinion.
    11. trans

      The 2 trans internals are different and wont work.
      Better you use a 4 cylinder 02A bellhousing on the VR trans.
      Then you will also need the other parts... Flywheel, clutch, slave and master cyl....
    12. Replies
      18
      Views
      1,317

      trans

      Any one that exceeds the spec is good.
      If only you could atleast put a bolt kit in this trans and strengthen up the the diff roll pin that would make it better.
    13. Replies
      18
      Views
      1,317

      trans

      Most of the speed bump issues I see especially when too low is damaged oil pand and a piece of the bellhousing cracked or missing.
      That damage can be from the clutch assembly or the cross shaft in...
    14. Replies
      3
      Views
      637

      heated gear

      It appears to have been heated to be remove or it could have been heated being driven without gear oil. Check the teeth.
      If its the only set you have no choice... Install it and spin the trans over...
    15. Replies
      7
      Views
      698

      rivets

      The press does work as well and the rivet cant refuse to come out at that point either . Just once those rivet heads come off it takes me about 37 secs and they are all out. But you have had to...
    16. Replies
      7
      Views
      698

      Small amount of heat can help out. But do now...

      Small amount of heat can help out. But do now warp it.
      A small wooden box for support and an air hammer with a straight tip can work also.
    17. Replies
      7
      Views
      1,109

      trans

      Glad to help. You always got to look out for the " it has a diff in it " game.
    18. Replies
      6
      Views
      2,065

      Mr. Loops is correct. Also on some Mk3 020 trans...

      Mr. Loops is correct.
      Also on some Mk3 020 trans the date and trans code can be etced on the bellhousing side across from the selector shaft in case you dont see it on the bottom.
    19. Replies
      6
      Views
      834

      trans

      Did the trans ever grind before all this happened going into 2ND gear?
      The fine tooth synchro sleeve on 1st / 2nd might be going bad.
    20. Replies
      6
      Views
      816

      trans

      Its possibly it was reman.trans from VW show the date it was done.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4