Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    Fourtitude.com


    Search:

    Type: Posts; User: HGB

    Page 1 of 13 1 2 3 4

    Search: Search took 0.61 seconds.

    1. no 1st gear

      Did he ever grind 2nd gear a few times?
      Its possible the 1st/2nd synchro sleeve and hub teeth got founded/peened over preventing the sleeve from sliding to 1st gear.
    2. Replies
      4
      Views
      162

      bracket

      Take the 3 rabbit studs out of the trans where the Mk1 style mount would go, get the Mk3 trans mount bracket and the 3 long bolts and set it up just like how the Mk3 trans is mounted.
    3. Replies
      3
      Views
      144

      5th gear

      Doing it without the proper tools, ...get a flat screw driver, place the 5th gear hub on its side, gear and sleeve touching the work bench on a piece of cardboard, slowly wedge the flat head between...
    4. Replies
      4
      Views
      160

      02M trans

      Hey. Did you check the gear oil level ?
      Does the 02M have the black caps at the end of the case side of the trans?
      Lets say you are in neutral, foot off the clutch at idle, any noise present?
    5. Thread: 02a diff into 02j

      by HGB
      Replies
      1
      Views
      175

      diff

      Yes, you will have to take out the right side seal flange, and the left side seal. Use 02A seals instead. Now you can use the stock 02A flanges with the 02A diff. Use a bently manual to help you out,...
    6. Replies
      7
      Views
      394

      noise

      That based on what you said would sound like a pinion bearing, or diff bearing, that have gone bad which usually makes noise on accel and decel.
      The input shaft bearings would make noise in neutral,...
    7. casing

      Yes it seems most of them end up that way during the casting process, yet some of them you wont see that, smooth with no imperfections.
      I have had them come in, full of gear oil, no leaks looking...
    8. Replies
      3
      Views
      316

      trans

      This almost sound like a ring gear issue but it can be anything. I had the over center spring inside the trans break and cause 1st and reverse to rub which creates a ratchet type noise, but usually...
    9. Trans

      I have seen many bellhousings looking like this, mostly 02A style. What you want to do is make sure the clutch side is ok.
      Most of the time the magnet catch the pieces of the 3rd and 2nd when the...
    10. center cap

      That I know as thats the way they came on the older trans, just did it for the hell of it and to keep the flanges out on the clip. In theory it would rub while turning, but after 8 years, its has no...
    11. center caps

      Hey. Well there is an older style center cap, metal and hole in the middle that is covered in rubber, it is thicker and would solve the issue. I just to a trans apart and tossed these away so I am...
    12. Replies
      4
      Views
      565

      trans

      Check the shifter cable, fluid level first. Is this all the gear including reverse?
      Any noise like a whine when shifted into gear?
    13. Replies
      2
      Views
      419

      trans

      It would sound like a worn or cracked synchro. Flushing wont work, it has to be removed opened up and verified.
    14. Replies
      1
      Views
      335

      trans

      More than likely the over center spring inside the trans broke. If it breaks then reverse gear and 1st gear tries to rub each other which give you the noise. Got to open it up to repair the issue.
    15. Thread: Vr6 tranny help

      by HGB
      Replies
      2
      Views
      389

      trans

      More than likely the input shaft bearings are worn. Or and bearing under and of the driven gears
    16. Replies
      4
      Views
      538

      trans

      Try bleeding bleeding the master cylinder first, cap it off, then fill the slave cylinder slowly...slowly so the fluid can go in and the air come out. Now connect the line and finish bleeding it...
    17. Replies
      2
      Views
      441

      trans

      More than likely when you dropped in the pothole and out of it, the wheel was air born for a split second and when the wheel touch the road again it slowed down the trans immediately which then takes...
    18. Replies
      3
      Views
      657

      noise

      Need more info.
      That noise almost sound like the exhaust manifold heat shields or a loose converter.
      Did you try to isolate the noise to the trans?
    19. Replies
      1
      Views
      597

      trans

      Is this noise a constant click/tap while in that particular gear?
      Or is it a click as you shift into a gear?
      It sounds like a bearing issue or possibly a broken / tooth on the ring or pinion.
    20. trans

      The 2 trans internals are different and wont work.
      Better you use a 4 cylinder 02A bellhousing on the VR trans.
      Then you will also need the other parts... Flywheel, clutch, slave and master cyl....
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4