Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    Fourtitude.com


    Search:

    Type: Posts; User: HGB

    Page 1 of 13 1 2 3 4

    Search: Search took 0.67 seconds.

    1. Replies
      3
      Views
      558

      noise

      Need more info.
      That noise almost sound like the exhaust manifold heat shields or a loose converter.
      Did you try to isolate the noise to the trans?
    2. Replies
      1
      Views
      513

      trans

      Is this noise a constant click/tap while in that particular gear?
      Or is it a click as you shift into a gear?
      It sounds like a bearing issue or possibly a broken / tooth on the ring or pinion.
    3. trans

      The 2 trans internals are different and wont work.
      Better you use a 4 cylinder 02A bellhousing on the VR trans.
      Then you will also need the other parts... Flywheel, clutch, slave and master cyl....
    4. Replies
      18
      Views
      1,201

      trans

      Any one that exceeds the spec is good.
      If only you could atleast put a bolt kit in this trans and strengthen up the the diff roll pin that would make it better.
    5. Replies
      18
      Views
      1,201

      trans

      Most of the speed bump issues I see especially when too low is damaged oil pand and a piece of the bellhousing cracked or missing.
      That damage can be from the clutch assembly or the cross shaft in...
    6. Replies
      3
      Views
      576

      heated gear

      It appears to have been heated to be remove or it could have been heated being driven without gear oil. Check the teeth.
      If its the only set you have no choice... Install it and spin the trans over...
    7. Replies
      7
      Views
      637

      rivets

      The press does work as well and the rivet cant refuse to come out at that point either . Just once those rivet heads come off it takes me about 37 secs and they are all out. But you have had to...
    8. Replies
      7
      Views
      637

      Small amount of heat can help out. But do now...

      Small amount of heat can help out. But do now warp it.
      A small wooden box for support and an air hammer with a straight tip can work also.
    9. Replies
      7
      Views
      1,037

      trans

      Glad to help. You always got to look out for the " it has a diff in it " game.
    10. Replies
      6
      Views
      1,828

      Mr. Loops is correct. Also on some Mk3 020 trans...

      Mr. Loops is correct.
      Also on some Mk3 020 trans the date and trans code can be etced on the bellhousing side across from the selector shaft in case you dont see it on the bottom.
    11. Replies
      6
      Views
      763

      trans

      Did the trans ever grind before all this happened going into 2ND gear?
      The fine tooth synchro sleeve on 1st / 2nd might be going bad.
    12. Replies
      6
      Views
      749

      trans

      Its possibly it was reman.trans from VW show the date it was done.
    13. Thread: No 5th Gear

      by HGB
      Replies
      3
      Views
      689

      trans

      That circled area should have a ball on it. It fell off over time due to heat from the dowm pipe. Just buy a new one.
    14. Replies
      7
      Views
      1,037

      Ok to check if an 02A, 02J, or 02M trans has a...

      Ok to check if an 02A, 02J, or 02M trans has a limited slip diff, simply remove the speedd sensor and take a good flash light and look in the hole. If the diff has a section that is cut open then...
    15. Replies
      15
      Views
      1,550

      the fork

      What about the clutch fork? Can it be bending while the pedal is down?
      You might want to try an older slave cylinder from an 02A trans like the G60.@
    16. Replies
      2
      Views
      579

      ata ring and pinion

      Some early ATA trans use the 020 style diff rivets, the bigger style came later on. Either one will work. I never had the ARP bolts break on either style. Yes the bigger bolts will be stronger when...
    17. Thread: Reverse issue

      by HGB
      Replies
      4
      Views
      1,020

      trans

      The click, depending on speed, is it a timely click or sounds like a ratchet?
      There is also an over center spring that can break and cause reverse and 1st gear to rub each other.
      Usually these...
    18. Replies
      16
      Views
      2,894

      02M

      For some reason, the 02Ms with the black cap over the rear input shaft bearings are the ones with this issue.
      Going with a ballbearing there to me was not a good idea. A tapered bearing would have...
    19. Replies
      4
      Views
      1,890

      trans

      Did it ever grind 2nd gear before?
      If the selector shaft brackets and arms are moving freely, then it might be internal... The 1st/2nd synchro sleeve thats going bad.
    20. Replies
      4
      Views
      1,890

      trans

      Did it ever grind 2nd gear before?
      If the selector shaft brackets and arms are moving freely, then it might be internal... The 1st/2nd synchro sleeve thats going bad.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4