Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    Fourtitude.com


    Search:

    Type: Posts; User: acee_dub

    Page 1 of 13 1 2 3 4

    Search: Search took 0.22 seconds.

    1. Replies
      7
      Views
      537

      Cool, thanks everyone for the input, very helpful...

      Cool, thanks everyone for the input, very helpful :beer:
    2. Replies
      4
      Views
      539

      Look into diesel truck, excavator or bus turbos.....

      Look into diesel truck, excavator or bus turbos.. many common vehicles came with holset turbos and you can probably source one from a scrapper or buy one online.. check out this thread for more...
    3. Replies
      7
      Views
      537

      This EBC, boost control works fine at lower...

      This EBC, boost control works fine at lower levels, raising by 10% from 0 - 100 duty cycle it slowly raised boost, and held steady at the mark.. in higher boost levels gets weird.. (at 100% duty only...
    4. Replies
      7
      Views
      537

      Maximum Boost? VRT

      I have a 12v VR6 on standalone (ms2 v3) I have maxed out the electronic boost controller settings in attempt to hit my 2BAR goal, however it would only peak at 1.2BAR, and lower off to 0.9BAR past...
    5. Replies
      7
      Views
      803

      Who makes this prefab stainless 3" exhaust you're...

      Who makes this prefab stainless 3" exhaust you're talking about? I have an mk3 vrt and need DP-Back 3" also located in ontario.. I don't think you can use mk3 exhaust on an mk2 though. But am not 100%
    6. Thread: bov rattle?

      by acee_dub
      Replies
      1
      Views
      314

      Can you post a youtube video with the sound you...

      Can you post a youtube video with the sound you are describing?
    7. Replies
      2
      Views
      459

      Look into Holsets,...

      Look into Holsets, http://forums.vwvortex.com/showthread.php?4894145-Holset-user-thread
    8. Replies
      3
      Views
      601

      If you are aiming for the best possible response,...

      If you are aiming for the best possible response, I would get the twin scroll housing, and pair it with a twin scroll manifold.. or maybe a quick spool flapper valve.
    9. Must be that rust colour spray job.. I'll get...

      Must be that rust colour spray job.. I'll get someone to rev it tomorrow and see where it's coming from, would be wicked if it isn't the pan, but I see the right side of it is really wet
    10. You mean these? http://i.imgur.com/BQFoFxZ.jpg...

      You mean these?

      http://i.imgur.com/BQFoFxZ.jpg

      http://i.imgur.com/sjy5KqU.jpg
    11. Oil Pan Leaking (Torqued proper + RTV on new gasket)

      I have reinstalled my oilpan with a new gasket, put Permatex Ultra Black on both sides of it and torqued to spec as per bentley, and it is still leaking. Could my bolts be stretched out or should I...
    12. Replies
      8
      Views
      1,087

      Solved! The problem was that the ignition...

      Solved!

      The problem was that the ignition input capture should have been set to Falling Edge.

      This can be tested for using a tooth logger

      Bad (2 long):
      http://puu.sh/isGxH/3299178402.png...
    13. Replies
      8
      Views
      1,087

      It seems the desync only occurs between 1100-1300...

      It seems the desync only occurs between 1100-1300 rpms, and if i keep it within that range, it will keep desyncing over and over

      -not noise
      -not dirty sensor
      -not tpsvref voltage

      Tried...
    14. Replies
      8
      Views
      1,087

      I removed and cleaned the sensor, reinstalled and...

      I removed and cleaned the sensor, reinstalled and retested to no avail.. Checked pin 26 of megasquirt with a multimeter when running and it was getting 4.86v, this value did not change when desyncing...
    15. Replies
      8
      Views
      1,087

      http://puu.sh/ihusl/9fd054c9c5.png ...

      http://puu.sh/ihusl/9fd054c9c5.png

      http://puu.sh/ihuKv/596e9380ac.png

      http://puu.sh/ihuQM/161d52167f.png

      http://puu.sh/ihv0l/4b59d309de.png

      The trigger log showed desync every time this...
    16. x2 Check for spark / fuel, getting a datalog of...

      x2 Check for spark / fuel, getting a datalog of it cranking helps see whats going on, if you post it up here it helps us to watch the replay of it through megalogviewer (you can make a log through...
    17. Replies
      8
      Views
      1,087

      SOLVED MS2 v3.0 on 12v VRT (Desyncing @ 1000~ rpm)

      Hi, I just got my VRT running on MS2v3 and have been getting fluctuating RPM / Leaning out when adding throttle gradually from idle (occurs around 1000rpm mark)
      shown in video:

      ...
    18. Replies
      1
      Views
      530

      figured it out, the steering column shaft had...

      figured it out, the steering column shaft had collapsed, i extended it to the marked position:

      http://puu.sh/awJeO/2f068dd01f.jpg

      http://puu.sh/awJdd/f05639d0d5.jpg
      ...
    19. Replies
      1
      Views
      530

      Steering Rack U-Joint Question (B4/GLX)

      Hi, I had my 98 GLX Jetta ZF steering rack die on me and have swapped in a B4 GLX Passat ZF rack, however I can not get the connecting sleeve over the upper u-joint fully, does anyone know if the B4...
    20. Replies
      18
      Views
      3,156

      The TIP122 was bad, I must have burnt it from all...

      The TIP122 was bad, I must have burnt it from all the re-soldering I was doing upon initial installation.
      Ordered a new one off DigiKey, threw it on, and it is looking good. Next I will need to get...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4